INSTALLATION AND OPERATION MANUAL
Free-Standing
EPA Certified
Wood-Burning Stoves
Save These Instructions
For Future Reference
Performer ST210
and SWS210
P/N 775215M, Rev. F, 09/2011
Performer SS210
Wood Stoves
Models Performer™ SS210,
ST210 and SWS210
A French manual is available upon request. Order P/N 775215CF.
Ce manuel d’installation est disponible en francais, simplement en faire la demande. Numéro de la
pièce 775215CF.
This appliance must be properly installed and operated in order to prevent the pos-
sibility of a house fire. Please read this entire installation and operation manual
beforeinstallingandusingyourwoodstove.Failuretofollowtheseinstructions
could result in property damage, bodily injury or even death. Contact your
local building or fire officials to obtain a permit and information on any
installationrequirementsandinspectionrequirementsinyourarea.
Portland
US
Report # 050-S-03b-2
WARNINGS
• Hot! Do not touch! The glass and surfaces of this appliance will
be hot during operation and will retain heat for a while after
shutting off the appliance. Severe burns may result.
• Carefully supervise children in the same room as appliance.
ing season to check for soot and creosote accumulations.
Any accumulations over 1/8” thick should be removed by
a professional chimney sweep. Do not attempt to burn out
heavy creosote accumulations with a hot fire. If large ac-
cumulationsareoccurring,reviewyourburningprocedures.
14. Ifacreosotefireshoulddevelop,thefiredepartmentshould
be called immediately and then attempts should be made
to control the fire until assistance arrives. If a “runaway”
fire should develop causing over-heating of the stove, the
door and draft regulators should be closed immediately.
The fire should die down once deprived of oxygen. After a
severe chimney fire, the complete chimney system should
be checked before further use.
IMPORTANT SAFETY AND WARNIING
INFORMATION
READ THIS MANUAL IN ITS ENTIRETY AND UNDER-
STAND THESE RULES TO FOLLOW FOR SAFETY.
1. When this room heater is not properly installed, a house
fire may result. To reduce the risk of fire, follow the instal-
lation instructions. Contact local building or fire officials
aboutrestrictionsandinstallationinspectionrequirements
in your area.
2. Wear gloves during installation to avoid injury from sharp
edges on the stove and/or its parts.
3. This unit is designed and engineered to burn only dry, well-
seasoned wood. Burning wet wood will greatly reduce the
stove’s efficiency, produce excessive amounts of smoke
and can cause dangerous chimney fires due to creosote
build-up.
4. Beforeopeningthedoor,thedraftcontrolmustbefullyopen
to avoid possible combustion flash (ignition of hot volatile
gases as the door is opened).
5. Never use gasoline, gasoline-type lantern fuel, kerosene,
charcoallighterfluid,orsimilarliquidstostartor’freshenup’
a fire in this heater. Keep all such liquids well away from
the heater while it is in use. DO NOT USE CHEMICALS OR
FLUIDS TO START THE FIRE.
6. Whileburning, fuelutilizesoxygenfromtheairintheroom.
Be sure to allow an adequate amount of fresh air into the
room where the stove is burning.
7. The outside surface of the stove will be hot while burning
properly and can set items like clothing and curtains on
fire. Keep furnishings and other combustible materials
away from the stove. Using the heat from the stove to dry
wet clothing can be hazardous if clothes are placed too
near the surface of the stove.
15. Do Not Use Grate Or Elevate Fire - Build Wood Fire Directly
On Hearth (firebrick). Do not use andirons or other methods
of supporting the fuel.
16. Please read this entire manual before you install and use
your new room heater. Failure to follow instructions may
result in property damage, bodily injury, or even death.
17. Checkalllocalbuildingandsafetycodesbeforeinstallation.
The installation instructions and appropriate code require-
ments must be followed exactly and without compromise.
In the absence of local codes the following standards and
codes must be followed.
18. In the U.S.A, install in accordance with the National Fire
Protection Association’s Code, NFPA 211, Standards for
Chimneys,Fireplaces,VentsandSolid-Fuel-BurningAppli-
ances, or similar regulations, may apply to the installation
of a Solid-Fuel-Burning appliance in your area. In Canada,
the guideline is established by the CSA Standard, CAN/
CSA-B365-M93, Installation Code for Solid-Fuel-Burning
Appliances and Equipment.
19. DO NOT CONNECT TO OR USE IN CONJUNCTION WITH ANY
AIR DISTRIBUTION DUCTWORK UNLESS SPECIFICALLY
APPROVED FOR SUCH INSTALLATIONS.
20. WARNING: BURNING IMPROPER FUEL (I.E. CHARCOAL)
CAN RESULT IN CARBON MONOXIDE POISONING, WHICH
MAY LEAD TO DEATH!
21. CarbonMonoxidePoisoning–Earlysignsofcarbonmonox-
ide poisoning resemble the flu with headaches, dizziness,
or nausea. If you have these signs, get fresh air at once!
Havetheheaterinspectedbyaqualifiedservicetechnician.
Some people are more affected by carbon monoxide than
others. These include pregnant women, people with heart
or lung disease or anemia, those under the influence of
alcohol, and those at high altitudes.
22. Failure to use manufacturer provided parts, variations in
techniquesandconstructionmaterialsorpracticesotherthan
those described in this manual may create a fire hazard and
void the limited warranty.
8. HOT WHILE IN OPERATION. KEEP CHILDREN, CLOTHING
FURNISHINGSANDCOMBUSTIBLEMATERIALACONSIDER-
ABLEDISTANCEAWAY. CONTACTMAYCAUSESKINBURNS.
Do not allow children to play near the stove without close
supervision. Do not touch the stove while it is burning.
Use extreme caution while the unit is in use. Surface tem-
peratures become dangerously hot and can cause serious
burns.
9. Donotallowanyonetooperatethestovewhoisnotfamiliar
with the operating instructions.
10. Attempts to achieve heat output rates that exceed stove
design specifications can result in permanent damage to
the stove. Never leave your stove unattended on high burn
rates. This may cause overfiring. Overfiring the stove may
cause a house fire. If the stove glows, you are overfiring.
11. Keep a water hose or hand-operated fire extinguisher close
for safety.
23. Do not make any make-shift compromises during installa-
tion. Any modification or alteration may result in damage
to the appliance or dwelling and will void the warranty,
certification and listings of this unit.
12. Smoke Detectors - Since there are always several poten-
tial sources of fire in any home, we recommend installing
smoke detectors. If possible, install the smoke detector in
a hallway adjacent to the room (to reduce the possibility
of occasional false activation from the heat produced by
the stove). If your local code requires a smoke detector
be installed within the same room, you must follow the
requirements of your local code. Check with your local
building department for requirements in your area.
13. Inspectyourchimneyatleastonceamonthduringtheburn-
24. These appliances are designed as supplemental heaters.
Therefore, it is advisable to have an alternate heat source
when installed in a dwelling.
25. Do Not Overfire – If Heater or Chimney Connector Glows,
You Are Overfiring.
26. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERV-
ING ANOTHER APPLIANCE.
27. DO NOT BURN GARBAGE OR FLAMMABLE FLUIDS SUCH
AS GASOLINE, NAPHTHA OR ENGINE OIL.
3
performance problems as well as be a safety hazard. A draft test should
read greater than .04’ W.C. (inches water column) and less than .08”
W.C. As per NFPA-211 standard (see paragraph below), the installer
must take into account all variables within the installation and install the
appliance in such a manner that satisfies the draft requirements of the
appliance. See Chimney Guidelines below to assist you in selecting the
proper venting system for your installation.
TESTING INFORMATION
Thismanualdescribestheinstallationandoperationofthesenon-catalytic
wood heaters. These heaters meet the U.S. Environmental Protection
Agency’s emissions limits for wood heaters sold on or after July 1, 1990.
This heater has been developed, tested and constructed in accordance
with the requirements of UL 1482, ULC S627 and HUD standards and
is listed by OMNI Test Laboratories, Portland, OR. It has been approved
for residential, mobile home and alcove installations.
American National Standards Institute ANSI/NFPA 211, Standard for
Chimneys, Fireplaces, Vents, and Solid Fuel-Burning Appliances
- See Draft Section: A chimney or vent shall be so designed and con-
structed to develop a flow sufficient to completely remove all flue and
vent gases to the outside atmosphere. The venting system shall satisfy
the draft requirements of the connected appliance in accordance with the
manufacturer’s instructions.
DRAFT REqUIREMENTS
Your wood stove is dependent upon a properly functioning chimney for
optimum performance. It is a high efficiency appliance that loses much
less heat up the chimney than older appliances and fireplaces. For this
reason it is important to match the stove to the chimney. The chimney
has two functions:
Chimney Guidelines:
• This appliance requires approximately 12 feet minimum of “effective
draw” provided by the venting system. As a rule of thumb, every 90
degree total direction change in the venting will result in a loss of
approximately 5 feet of “effective draw.” Example: If two 45 degree
offsets are used, subtract 5 feet from the actual vertical vent height
to determine your “effective draw.” In this case if you had 14 feet of
vertical vent, the effective draw would only be approximately 9 feet
(14 ft. - 5 ft. = 9 ft.), therefore it may be necessary to add additional
height to the venting system.
• Do not install an offset within the first two feet above the flue outlet
on the appliance.
• Inwellinsulatedandweathertighthomes,itmaybedifficulttoestablish
a good draft up your chimney. The poor draft is caused by a shortage
of air in the house. In this situation an Outside Air Kit may need to
be installed (See Negative Pressure Warning on Page 5 and Outside
Combustion Air on Page 11).
1. It draws combustion air into the appliance (without air, no fuel will
burn) and
2. It exhausts combustion by-products. Your new appliance is what is
known as a “natural draft” appliance.
The appliance depends solely on the natural draft of the chimney system
to draw combustion air into the unit. Draft is the force that moves air
from the appliance up into the chimney. The amount of draft in your
chimney depends on the length of the chimney, local geography, nearby
obstructions and other factors. Too much draft may cause excessive
temperatures in the appliance (overfiring). Slow or inadequate draft
equals poor combustion and possible smoking problems. The following
are some conditions that may contribute to poor chimney draft:
1. A chimney too large for your appliance.
2. A chimney with not enough height to produce adequate draft.
3. A chimney with excessive height (this may allow exhaust to cool too
much before exiting, which will stall the rate the exhaust exits).
4. Offsets in the venting system are too restrictive (see Chimney Guide-
lines).
Inadequate draft will cause the appliance to leak smoke into the room
through the stove and the chimney connector joints.
Chimney Height Requirements
The chimney must extend 3’ (.92m) above the level of roof penetration
and a minimum of 2’ (.61m) higher than any roof surface within 10’
(3m) (see below). Check with your local building officials for additional
requirements for your area.
Excessive draft may cause an uncontrollable burn or a glowing red stove
or chimney part.
Less than
10' (3 m)
Overfiring Damage - If the heater or chimney connector glows, you are
overfiring. Other symptoms may include: Cracking, warping or burning
out of components, plated accessories may turn color, stove glass may
develop a haze, which will not come off with cleaning.
2’ (610 mm) Min.
3' (914 mm)
3'
Min.
10'
(3 m)
(914 mm)
Overfiring of a stove is a condition where excessive temperatures are
reached, beyond the design capabilities of the appliance. The damage
that occurs from overfiring is not covered under the manufacturer’s
limited warranty.
Min.
Also see Troubleshooting on Page 20.
Figure 1 - Chimney Height Requirements
SELECTING THE PROPER VENTING SYSTEM
To pass inspection in nearly any jurisdiction, the chimney must meet both
safety and exhaust flow requirements. The (3’ by) 2’ by 10’ rule applies
to both masonry and factory-built chimneys.
The appliance is merely one component of a larger system. The other
equally important component is the venting system. This is necessary for
achieving the required flow of combustion air to the fire chamber and for
safely removing unwanted combustion byproducts from the appliance.
If the venting system’s design does not promote these ends, the system
maynotfunctionproperly.Poorlyfunctioningventingsystemsmaycreate
* Ref. USA - National Standard, NFPA 211-latest edition and Canada
National Standard CSA B365-01-latest edition. Vents installed with a
listed cap shall terminate in accordance with the terms of the cap’s
listings.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
4
NEGATIVE PRESSURE WARNING
FUEL
This appliance is not designed to be operated in a negative pressure.
In very airtight homes with large kitchen exhaust fans, furnace cold air
returns, fresh air exchange systems and any other air system in close
proximity to the heating appliance may create a negative pressure in the
same room as the heating appliance. This can create dangerous back
draftingofthestoveandchimneyjoints,drawingcombustionby-products
into the home. Be sure your home has adequate makeup air to eliminate
negative pressures caused by the above-mentioned sources. Outside air
connected to the appliance probably will not resolve such a problem as
the stove or fireplace insert is not the source of negative pressure. Lennox
Hearth Products accepts no liability for damages resulting from negative
pressures described here.
Thisunitisdesignedandengineeredtoburn,dry,well-seasonedwoodonly.
Dry, seasoned wood is that which has been cut, split and allowed to dry
under a covered area where air is free to flow and circulate under and
around the wood (not under a tarp or plastic). Make sure wood is not
stacked directly on the ground, it may absorb moisture from the ground.
It should be allowed to dry in these conditions for a minimum of six
months, preferably one year or more. IT MUST BE UNDERSTOOD
THAT WOOD CANNOT BE LEFT IN ANY KIND OF WET OR DAMP
AREA OR IT WILL NEVER BECOME COMPLETELY SEASONED.
Your stove will not operate at the level that it is meant to unless you use
seasoned, dry wood. Do not burn driftwood or wood that has been in salt
water, doing so will void your warranty. Do not burn treated wood, coal,
garbage, cardboard, solvents, or colored paper. Burning treated wood,
garbage, solvents, or colored paper may result in the release of toxic
fumes. This type of burning will also void your warranty.
Ventilation Requirements - Provide adequate air for combustion. The
fresh air requirements of this appliance must be met within the space
where it will be installed. Ventilation is essential when using a Solid-Fuel-
Burning heater. In well insulated and weather tight homes, it may be
difficult to establish a good draft up the chimney (caused by a shortage
of air in the home). The lack of air is caused by many common household
appliances which exhaust air from the home (such as a furnace, heat
pump, air conditioner, clothes dryer, exhaust fans, fireplaces, and other
fuel burning appliances). Also, the combustion process of this heater
uses oxygen from inside the dwelling. If the available fresh air delivery
in the dwelling is insufficient to support the demands of these appliances,
problems can result (i.e. excessive negative pressure can develop in the
dwelling which will affect the rate at which this appliance can draft thus
resulting in performance problems. To correct this problem it may help
to open a window (preferably on the windward side of the house) or
install an optional outside air kit.
Do Not store fuel within space heater installation clearances or within
the space required for refueling and ash removal.
PAINT CURING
Ifyourstovehasplatedaccessories,besuretocleanitwithahousehold
type glass cleaner and a very soft cloth to remove any fingerprints and
residues prior to the first fire and before any fire if the gold has been
handled or soiled. Do not close the door tightly during the “Burn-In
Period.”Also,openthedoorfrequently(every5-10minutes)tokeepthe
gasket from adhering to the curing paint. Ventilate the house well during
these first firings as the paint gives off carbon dioxide and unpleasant
odors. It is recommended that persons sensitive to an imbalance in the
indoor air quality avoid the stove during the curing process.
CREOSOTE FORMATION AND NEED FOR REMOVAL
When wood is burned slowly, it produces tar and other organic vapors,
which combine with expelled moisture to form creosote. The creosote
vapors condense in the relatively cool chimney flue of a slow-burning
fire. As a result, creosote residue accumulates on the flue lining. When
ignited, this creosote makes an extremely hot fire.
Your new appliance is painted with a high temperature paint that cures
duringthefirstfewfirings.Werecommendthatyouputyourstovethrough
a regimen of three burns. The first two should last for 20 minutes each
at 250 degrees (the stove should be allowed to cool completely between
each burn). The third should be a burn of at least 450 degrees F. for 45-60
minutes. The paint will become soft, gummy and emit non-toxic smoke
during these burns. After the stove cools down for the third time, the
paint will harden. DO NOT BUILD A LARGE ROARING FIRE UNTIL
THIS CURING EFFECT IS COMPLETE OR YOU MAY DAMAGE THE
FINISH OF YOUR STOVE. Spray can touch-ups should be done only
with a high temperature stove paint (cat. no. H8159), available from all
Lennox Hearth Products dealers.
The chimney and chimney connector should be inspected at least once
monthly during the heating season to determine if a creosote buildup has
occurred. If creosote has accumulated (1/8” [3 mm] or more), it should
be removed to reduce the risk of a chimney fire.
Establish a routine for the fuel, wood burner and firing technique.
Check daily for creosote build-up until experience shows how often
you need to clean to be safe. Be aware that the hotter the fire the
less creosote is deposited, and weekly cleaning may be necessary
in mild weather even though monthly cleaning may be enough in
the coldest months. Contact your local municipal or provincial fire
authority for information on how to handle a chimney fire. Have a
clearly understood plan to handle a chimney fire.
BURN-IN PERIOD
Please be patient with the heat output of your stove for the first few
weeks. The steel will go through a curing process that eliminates mois-
ture, which is deep in the steel and firebrick. This moisture will reduce
initial heat output of your stove and may make it difficult to start. After
you have broken in the paint on the stove it will be necessary to build
hot fires to thoroughly remove the moisture from the appliance. Running
the stove with the draft fully open for 1 to 1-1/2 hours after starting and
adding generous amounts of fuel during the first week or two should
complete the curing process. We recommend the use of a thermometer
attached to the stovetop or chimney. Temperatures on the connector pipe
should run in the 250-600 degree range. (DO NOT OVERFIRE THE
STOVE DURING THIS PROCESS. IF THE STOVE OR CHIMNEY
BECOMES RED, REDUCE THE AMOUNT OF AIR ENTERING THE
STOVE IMMEDIATELY).
DISPOSAL OF ASHES
Ashes should be scooped out of a cool stove with a small metal shovel.
Ashesshouldbeplacedinametalcontainerwithatightfittinglidandmoved
outdoors immediately. Other waste shall not be placed in this container.
The closed container of ashes should be placed on a non-combustible
floor or on the ground, well away from all combustible materials, pending
final disposal. If the ashes are disposed of by burial in soil or otherwise
locally dispersed, they should be retained in the closed container until
all the cinders have thoroughly cooled. Ashes can ignite up to 72 hours
after removal from the stove.
5
Chimney and Connector
CLEARANCES TO COMBUSTIBLES
Minimum 6" diameter, minimum 24 MSG black steel connector pipe with
UL103HT listed factory-built chimney suitable for use with solid fuels
or masonry chimney. Horizontal connection not tested, refer to local
building codes for installation. See installation instructions for details.
Restrictions apply! Read instructions before installing.
WARNING: BEABSOLUTELYSURETHEDISTANCEBETWEENTHE
HEATERANDTHESURFACEOFANYCOMBUSTIBLECONSTRUC-
TION IS NOT LESS THAN SHOWN IN THE FIGURES ON PAGE 7.
Floor Protection
Residential chimney systems must be from the same brands as listed
for mobile homes but connector pipe may be double wall, single wall or
single wall with shield as listed above.
USA - The floor in front and under the heater must be protected with
noncombustible material. The covering must extend 16” in front of the
door opening of the heater and 8” to either side of the door opening.
This appliance may be vented into a code-approved masonry chimney
with flue liner.
Canada - The floor in front and under the heater must be protected with
noncombustible material. The covering must extend 457 mm in front of
the door opening of the heater and 200 mm to either side of the stove
body and 200 mm to the rear or to the wall, whichever is smaller.
Warning:Chimneyconnectormustbeingoodconditionandkeptclean.
Do not install damaged parts.
USA and Canada - A chimney connector / venting extends horizontally
over the floor, protection must also cover the floor under the connector
/ venting and at least 2” (51 mm) to either side.
All of the stove connector pipe used must be of the same brand. The
chimney that the stove pipe transitions into may be a different brand.
Other than the transition of the stove pipe into the chimney, do Not mix
different brand vent components. Install all vent components per vent
manufacturer’s instructions.
Reduced Clearances
The chimney connector shall not pass through an attic or roof space,
closet or similar concealed space, or a floor, or ceiling. Where passage
through a wall, or partition of combustible construction is desired, the
installation shall conform to CAN/CSA-B365, Installation Code for Solid-
Fuel-Burning Appliances and Equipment.
Clearances to combustible surfaces can be reduced with the use of listed
double wall connector pipe. See the clearances with double wall pipe on
the following page.
Alcove Clearances:
Theremustbeaneffectivevaporbarrieratthelocationwherethechimney
or other component penetrates to the exterior of the structure. Follow the
vent manufacturer's detailed instructions.
In alcove installations, only 6” double wall connector pipe can be used
(single wall or single wall pipe with shield is not allowed). Minimum alcove
width between combustible materials is 48” (1219 mm). Maximum alcove
depth is 48” (1219 mm). Minimum alcove height is 72” (1829 mm).
IMPORTANT NOTE: See Draft Requirements and Selecting a Proper
Venting System on Page 4 to assist you in choosing the proper venting
system for your installation.
Clearance dimensions are to flue collar. If a single wall connector pipe
with shield is used, a 1 inch air space is needed between pipe and shield.
Shield attaches to rear of stove pipe and must run from stove top to ceil-
ing. Pipe shield shall be UL listed.
Components Required For Installations
Legs AND Bottom Heat Shield or Pedestal Base. If optional blower is
NOT used, Rear Heat Shield Block Off Plate shall be installed.
Use all required components specified for this appliance. Do
not substitute.
WARNING: In the event that you remove the blower for any
reason, make sure a cover plate (available from Lennox Hearth
Products) is installed before using the heater. Excessive rear
wall temperatures will result if the stove is burned without the
cover plate. Note: The cover plate is not necessary if a blower
has never been installed because a knock-out will be in place
to act as the cover.
* Other approved chimney brands are Projet, Jakes Evans/GSW, Dura-
vent, Metal Fab, Ameri-Tec, Metalbestos and Industrial Chimney (ICC).
6
INSTALLATION CLEARANCES - REFER TO FIGURES 2, 3 ANd 4
PIPE
Single Wall
INSTALLATION
Residential
A
B (1)
13-3/4”
349mm
C
D (1)
14-1/2”
368mm
E†
8”
200mm
F (1,4)
9”
229mm
USA-16”
CAN-483mm
USA-24”
CAN-635mm
Residential
USA-10”
CAN-330mm
7-3/4”
197mm
USA-24”
CAN-635mm
14-1/2”
368mm
8”
200mm
9”
229mm
v
Single w/ Pipe
Shield
Double Wall
Double Wall
Residential or
Mobile Home*
USA-10”
7-3/4”
USA-18”
8-1/2”
8”
6”
CAN-330mm
197mm
CAN-483mm
216mm
200mm
152mm
Alcove
USA-10”
CAN-330mm
7-3/4”
197mm
USA-21”
CAN-559mm
8-1/2”
216mm
8”
200mm
6”
152mm
PIPE
Single Wall
INSTALLATION
Residential or Alcove
G (4)
USA-18”
CAN-533mm
H (2)
USA-37-3/4”
CAN-1213mm
I (6)
USA-51”
CAN-1422mm
J (2)
USA-34-3/4”
CAN-1048mm
K
L (5)
USA 0"
USA-16”
CAN-450mm CAN-200mm
Residential or Alcove
USA-18”
CAN-533mm
USA-37-3/4”
CAN-1213mm
USA-45”
CAN-1270mm
USA-34-3/4”
CAN-1048mm
USA-16”
USA 0"
v
Single w/
CAN-450mm CAN-200mm
Pipe Shield
Double Wall
Air-Cooled
Residential or Alcove
or Mobile Home*
USA-15”
CAN-450mm
USA-37-3/4”
CAN-1213mm
USA-45”
CAN-1270mm
USA-34-3/4”
CAN-1048mm
USA-16” USA 0"
CAN-450mm CAN-200mm
Double Wall
Alcove
N/A
USA-37-3/4”
CAN-1213mm
USA-45”
CAN-1270mm
USA-34-3/4”
CAN-1048mm
USA-16” USA 0"
CAN-450mm CAN-200mm
Top View
Corner Clearance, Stove and Flue to Wall
PIPE
Single Wall
INSTALLATION
Residential or Alcove
M
84”
2134mm
T (6)
USA-61-3/4”
CAN-1619mm
Residential or Alcove
84”
2134mm
USA-61-3/4”
CAN-1619mm
v
Single w/
Pipe Shield
Double Wall
Air-Cooled
Residential or Alcove
or Mobile Home*
72”
USA-57-1/2”
CAN-1727mm
1829mm
G
G
F
F
Double Wall
Alcove
72”
1829mm
USA-57-1/2”
CAN-1727mm
T
†
USA=8" (200mm) from door opening, Canada=8" (200mm) from sides and back of unit
6” Ø Flue Collar
u
v
Dimensions to Stove Body
Clearances may only be reduced by means approved by the regulatory authority.
* Mobile Home - USA only
Floor
Protection
K
Figure 4
Top View-Parallel Installation
Footnotes:
48”
Max.
Depth
1- These dimensions to the stove body are
forreferenceonly. Actualdistancesshould
be measured from the stove’s flue collar.
2- Minimum noncombustible hearth pad
dimensions.
B
A
L
Side View-Alcove and
Parallel Installations
3- Shield shall be attached to the rear of the
stovepipewitha1”airspaceandmustrun
from the top of the stove to the ceiling.
4- Not applicable to alcove installations.
5- In corner applications, when installed
at minimum back wall clearances, the
required floor protection is dimensioned
off the back plane of the stove, therefore
the floor protection required off the back
corners (at a 45 degree angle) only needs
to extend to the wall. This situation will
only occur in CANADA installations.
6- Reference dimension only, to assist in
planning the installation.
C
M
D
I
H
†E
†E
K
Floor Protection
J
FLOOR PROTECTION
Clearances to connector pipe shall be mea-
sured from the flue collar of the stove.
Figure 2
I
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
7
Figure 3
Single Wall Pipe
Using 6” Diameter Single Wall Connector Pipe
STAINLESS STEEL LINER
Using 6” Diameter Rigid Stainless Steel Liner
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!
Chimney
Chimney
Termination
Cap
Termination
Rain Cap
Shown with Tubinox™ Stainless
Steel Liner components (see Page
29 for ordering information)
Storm
Collar
Flashing
Roof
Flashing
Ceiling Support
Assembly
Length
18” (457mm)
Minimum
Masonry
Adaptor
Slip
Adaptor
Single wall stove pipe
must not pass through
attics, closets, walls or
ceilings. It is used to
connect this appliance
to a factory built or
90° Tee
masonry chimney.
Fasten each stove pipe
connection with at least
3 sheet metal screws.
Chimney
Connector
6” x 24” 24-gage
black steel or 26
gage blued steel
single wall pipe
Floor
Protector
Stove
Side View
Fasten stove pipe to
flue collar with 3 sheet
metal screws.
Figure 6 - Connected to a Masonry Chimney
Floor
Protector
Stove
Side View
YOUR CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL
BUILDING AND FIRE CODES.
Figure 5 - Typical Installation
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
8
CHIMNEY INSTALLATION
Double Wall Pipe
•
•
Install chimney as per manufacturer’s instructions. Some brands of
pipe may require removal of the spacer ring in the flue collar.
All horizontal runs of pipe should be as short as possible and are
required by NFPA No. 211 to have an upward pitch or rise in the same
direction the smoke travels of no less than 1/4” to the linear foot. The
connector pipe must meet minimum clearances in any direction to
walls or other combustible materials. It must attach to a listed double
wall metal chimney at least 6” in diameter or to a masonry chimney
with a flue passage of at least 48 square inches.
It is required that a chimney connector pipe not extend further than
the inner wall of the flue when it is connected to a masonry chimney
and that it either be cemented to the masonry or be installed without
cement in a thimble connected to the masonry wall. When the
connector is inserted into a thimble, the joint must be tight enough
so that it will not be dislodged in normal use. Install connector at
no less than the minimum clearances from the ceiling when using a
90-degree elbow to pass through combustible constructions.
Chimney connector pipes should never pass through a floor, ceiling,
fire wall, partition, or combustible construction of any type unless
certain precautions are taken. The best method is to use a listed
thimble and a listed chimney in accordance with the manufacturer’s
directions. NFPA No. 211 gives approved methods for passing a flue
pipe through combustible constructions (see Page 10).
Using 6” Diameter Type L-Vent Connector Pipe
Mobile (Manufactured) Home Installation Shown
INSTALL VENTING SYSTEM PER VENT MANUFACTURERS
INSTRUCTIONS!
Mobile home installations
require a spark arrestor at the
chimney termination.
Termination Cap
with Spark Arrestor
Remove, if mobile
home is transported
•
•
Storm
Collar
3 Feet
Minimum
Flashing
Support
Box
Fasten each stove pipe
connection with at least
3 sheet metal screws.
Manufactured Home Installations
(ref. Figure 7)
All mobile home installa-
tions require an outside
air kit (see Page 28 for
ordering information)
and the stove must be
secured to the floor and
grounded to the mobile
home chassis.
DVL Close
Minimum of
12-15’ of Flue
to achieve a
stable draft.
Clearance
This appliance is approved for installation into a manufactured
(mobile) home in the USA ONLY!
Connector Pipe
Installation should be in accordance with the Mobile Home
Construction and Safety Standard, Title 24 CFR, Part 3280 (in
Canada CAN/CSA Z240 MH), or, when such a standard is not
applicable, the Standard for Mobile Home Installations, ANSI
A225.1.
7 Feet
Minimum
Fasten stove pipe to
flue collar using 3
All mobile home installations require an outside air kit (see Page 28
for ordering information). The stove must be secured to the floor and
grounded to the chassis of the mobile home.
sheet metal screws.
WARNING: DO NOT INSTALL IN SLEEPING ROOM OF A MOBILE
HOME.
CAUTION: THESTRUCTURALINTEGRITYOFTHEMOBILEHOME
FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED.
Floor
Protector
SecureStove
to floor
Approved Chimney* - Your stove is approved for use with Class A, UL
103 HT (U.S.) / ULC-S629 (Canada) Listed Residential Type and Building
Heating Appliance Chimney (HT chimney - 2100° Fahrenheit) and double
wall connector pipe from Security™ Chimneys.
Stove
Side View
Floor
Install Outside Air
Chassis
Clearancestoconnectorshallbemeasuredfrom6”fluecollar.Restrictions
apply! Read instructions before installing.
Kits per instructions
on Page 11
Grounded to Steel Chassis
using a #8 AGW copper
wire or equivalent.
YOUR CHIMNEY INSTALLATION MUST COMPLY WITH LOCAL
BUILDING AND FIRE CODES.
Figure 7 - Typical Installation
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
9
Chimney Connector Systems and Clearances from Combustible
Walls for Residential Heating Appliances (NFPA 211) Refer to
Figure 8
System A
Minimum chimney clearance to brick
and combustibles 2 in. (51mm)
Minimum clearance
System A. Minimum 3.5 in. (90 mm) thick brick masonry wall
framed into combustible wall with a minimum of 12 in. (305 mm)
brick separation from clay liner to combustibles. Fireclay liner (ASTM
C 315, Standard Specification for Clay Flue Linings, or equivalent),
minimum5/8in. (16mm)wallthickness, shallrunfromoutersurface
of brick wall to, but not beyond, the inner surface of chimney flue
liner and shall be firmly cemented in place.
12 in. (305mm)
of brick
Chimney
flue
Chimney
connector
Fire clay
liner
Minimum
Masonry chimney
constructed to NFPA 211
Clearance: 12 in. (305 mm)
12 in. (305mm)
to combustibles
System B. Solid-insulated, listed factory-built chimney length of the
same inside diameter as the chimney connector and having 1 in.
(25.4 mm) or more of insulation with a minimum 9 in. (229 mm) air
spacebetweentheouterwallofthechimneylengthandcombustibles.
Minimum Chimney Clearance from Masonry to Sheet Steel
Supports & Combustibles – 2 in. (51mm)
System B
Min. Clearance
9 in. (229mm)
Nonsoluble
Refractory
Cement
The inner end of the chimney length shall be flush with the inside of
the masonry chimney flue and shall be sealed to the flue and to the
brickmasonrypenetrationwithnon-water-solublerefractorycement.
Supports shall be securely fastened to wall surfaces on all sides.
Factory Built
Chimney Length
Chimney
Connector
Chimney Length
Flush with
Inside of Flue
UseChimney
Mfrs.Partsto
Attach
Fasteners between supports and the chimney length shall not pen-
etrate the chimney liner.
Air Space – 9 in.
(228.6mm) Min.
Chimney
flue
Connector
Clearance: 9 in. (229 mm)
Solid-Insulated
ListedFactory-
BuiltChimney
Length
Masonry chimney
constructed to NFPA 211
SystemC.Sheetsteelchimneyconnector,minimum24gauge[0.024
in. (0.61 mm)] in thickness, with a ventilated thimble, minimum 24
gauge [0.024 in. (0.61 mm)] in thickness, having two 1 in. (25.4
mm) air channels, separated from combustibles by a minimum of 6
in. (152 mm) of glass fiber insulation. Opening shall be covered, and
thimble supported with a sheet steel support, minimum 24 gauge
[0.024 in. (0.61 mm)] in thickness.
Sheet Steel Supports
System C
Minimum chimney clearance to sheet
steel supportrs and combustibles
2 in. (51mm)
2 Air Channels, Each 1
in. (25.4 mm)
Supports shall be securely fastened to wall surfaces on all sides and
shallbesizedtofitandholdchimneysection.Fastenersusedtosecure
chimney section shall not penetrate chimney flue liner.
Chimney
Connector
Chimney
flue
Clearance: 6 in. (152 mm)
2 Ventilated Air
Channels, Each
System D. Solid-insulated, listed factory-built chimney length with
an inside diameter 2 in. (51 mm) larger than the chimney connector
and having 1 in. (25.4 mm) or more of insulation, serving as a pass-
through for a single wall sheet steel chimney connector of minimum
24 gauge [0.024 in. (0.61 mm)] thickness, with a minimum 2 in.
(51 mm) air space between the outer wall of chimney section and
combustibles. Minimum length of chimney section shall be 12 in.
(305 mm). Chimney section concentric with and spaced 1 in. (25.4
mm) away from connector by means of sheet steel support plates
on both ends of chimney section. Opening shall be covered, and
chimney section supported on both sides with sheet steel supports
of minimum 24 gauge [0.024 in. (0.61 mm)] thickness.
1 in. (25.4 mm) Masonry chimney
Construction of constructed to NFPA 211
Sheet Steel
Sheet Steel Supports
Minimum chimney clearance to sheet steel
supports and combustibles 2 in. (51mm)
System D
Sheet Steel
Supports
Min. Clearance
2 in. (51 mm)
1 in. (25.4 mm)
air space to
chimney length
Chimney
Section
Chimney
Connector
Supports shall be securely fastened to wall surfaces on all sides and
shallbesizedtofitandholdchimneysection.Fastenersusedtosecure
chimney section shall not penetrate chimney flue liner.
Chimney connector
Chimney length
Sheet Steel Supports
Masonry chimney
constructed to NFPA 211
Air Space – 2 in.
(51mm) Min.
Clearance: 2 in. (51 mm)
Additional requirements:
Figure 8 - Chimney Connector Systems and Clearances from Combustible Walls
1.Insulation material used as part of wall pass-through system shall be
of noncombustible material and shall have a thermal conductivity of
1.0 Btu-in./hr-ft2 - ºF (4.88 kg-cal/hr-m2 - ºC) or less.
2.All clearances and thicknesses are minimums; larger clearances and
thicknesses shall be permitted.
3.Any material used to close up an opening for the connector shall be of
noncombustible material.
4.A connector to a masonry chimney, except for System B, shall extend
in one continuous piece through the wall pass-through system and the
chimney wall to the inner face of the flue liner, but not beyond.
10
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
LEG AND HEATSHIELD INSTALLATION
Note: The threaded rods used to bolt the legs to the stove are packaged
with the heatshield, as a heatshield is required when a stove is installed
on legs.
Residential and Mobile Homes
(Bolting down and grounding of stove are required only in mobile
homes).
Open all cartons, if any and remove the contents upon receipt and check
for any damaged or missing parts. If there is hidden damage, notify your
freight company or Lennox Hearth Products dealer immediately.
BACK
Heat Shield
Mounting Holes
CAUTION: Wear gloves during installation in case of sharp
edges on the stove.
FRONT
Air Channel
Leg Installation
Figure 10
1. Carefully place stove on it’s back. Be careful not to scratch the
stove, use a piece of cardboard or carpet to protect the back of
the stove.
OUTSIDE AIR KIT INSTALLATION
2. Mount all four legs as shown in Figure 9.
3. First, screw the threaded rods into the holes at the four corners
on the bottom of the stove. Screw the threaded rods into the
firebox three full rotations or 3/16 to 1/4”, (if the rear rods are
screwed in too far they will lift the bricks off the bottom of the
stove). Use a washer and nut to secure the leg. Be sure the
legs are mounted squarely on the firebox bottom. Tighten nuts
securely.
4. Use the two bolts and washers provided with the heatshield kit
to mount the heatshield as shown in Figure 10.
5. Do not over tighten the heatshield mounting bolts as it may bend
the heatshield.
To install the “Outside Air Kit,” position the clip so that the nut is directly
above the hole punched in the back of the heatshield (See Figure 11).
Install the outside air adapter box on the stove by sliding it into the air
channellocatedbetweenthebottomheatshieldandthestovebottomuntil
the oblong ring is approximately 1/4” from the rear edge of the lower
heatshield. Make sure the ring is facing down. Thread the 1/4” bolt up
through the nut in the clip until snug against the adapter box.
Expanded View of Clip
Line up the hole in the clip with the hole in the
rear center of the bottom heatshield
Threaded Rod
Washer
Nut
Clip
1/4” Bolt
Figure 11
To locate the hole in the hearth for outside air, mark a 4” circle on the
hearth. The circle’s center should be 2-3/4” directly back from the center
of the flue outlet and 5/8” to the left side.
Figure 9
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
11
14. All horizontal runs of pipe should be as short as possible and are
required by NFPA No. 211 to have an upward pitch or rise in the same
direction the smoke travels of no less than 1/4” to the linear foot.
The connector pipe must meet minimum clearances in any direction
to walls or other combustible materials. It must attach to a listed
double wall metal chimney at least 6” in diameter or to a masonry
chimney with a flue passage of at least 48 square inches.
15. It is required that a chimney connector pipe not extend further than
the inner wall of the flue when it is connected to a masonry chimney
and that it either be cemented to the masonry or be installed without
cement in a thimble connected to the masonry wall. When the
connector is inserted into a thimble, the joint must be tight enough
so that it will not be dislodged in normal use. Install connector at
no less than the minimum clearances from the ceiling when using
a 90-degree elbow to pass through combustible constructions.
16. Chimney connector pipes should never pass through a floor, ceiling,
fire wall, partition, or combustible construction of any type unless
certain precautions are taken. The best method is to use a listed
thimble and a listed chimney in accordance with the manufactures
directions. NFPA No. 211 gives approved methods for passing a
flue pipe through combustible constructions.
STOVE INSTALLATION
1. If not previously installed, install floor protection and move the
heater into the desired location.
2. Position the stove on your floor protection in the exact location
where it is to be located, making sure all minimum clearances are
met.
3. If you are installing outside air on your stove, mark a 4” circle on
the floor protection just below the oblong ring. When cut out, this
hole will accommodate the flexible outside air tube.
4. If the stove is to be fastened to the floor, locate the hold down
brackets inside the leg box and mark the floor protection below the
holes in the brackets.
5. If you are installing outside air on your stove, remove the stove and
cut the floor protection and the floor where the 4” air tube circle had
been previously drawn. If the stove is to be fastened to the floor,
drill 1/2” holes through the floor protection only, at the marks that
were for fastening the stove to the floor if so desired. Slip the flexible
outside air tube through the hole in the floor, leaving 1” of tube above
the floor protector surface, using tape to hold it in place.
6. Place the stove on the floor protection so that the previously cut or
drilled holes line up. Attach the stove to the floor with the lag bolts
if so desired.
7. If you are installing outside air on your stove, place the hose clamp
over the flexible air tube and slide the tube up over the 4” ring on
the outside air adaptor box and tighten the hose clamp. Push the
outside air adaptor forward 1/4” until full contact is made with the
lower heatshield. Tighten the 1/4” bolt until the adaptor box is held
firmly in place. Use silicone sealant to create a seal between the
flexible air tube and your floor protection.
8. If it is necessary to level, secure, or ground your stove, use the holes
in the bottom of the leg for those applications. To level the stove
on Olympic cast legs, locate the front leg that is not touching the
hearth pad. Insert the allen head screw through the slotted washer
(supplied with the legs) and into the threaded hole in the bottom of
the leg. See the drawing to the right. Push the slotted washer down
until it touches the hearth pad and then tighten the screw into the
leg. Should any other leg not be resting on the hearth pad, install a
washer and screw in that leg as well.
9. Install bricks and baffle as per instructions on Pages 14 and 15.
It is highly recommended that the baffle be assembled before the
chimney is installed so that the baffle blankets can be adjusted into
place through the flue collar.
Insert the allen
head screw
through the
slotted washer
10. If installed into a mobile home, the stove shall be grounded to the
mobile home chassis with a #8 AGW copper wire or equivalent.
11. For residential installations, install the first section of stove pipe
with the crimped end going down inside the flue collar on the heater.
Continue with your stove pipe, installing each section-crimped
end down. Make the final connection to your chimney. Your dealer
carries the necessary pipe and fittings to connect to the various
listed factory-built chimneys. YOUR CHIMNEY INSTALLATION MUST
COMPLY WITH LOCAL BUILDING AND FIRE CODES.
Figure 12
12. Be sure to fasten each stove pipe connection with at least 3 sheet
metal screws.
13. Install chimney as per manufacturer’s instructions. Some brands of
pipe may require removal of the spacer ring in the flue collar.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
12
5. If required, install the Outside Air Kit (P/N 71112) as per the fol-
lowing instructions. To locate the hole in the hearth for outside
air mark and cut a 4” (102 mm) hole in the hearth. The hole’s
center should be 3” (76 mm) directly forward from the center
of the flue outlet or locate as per the following instructions.
6. Position the stove on your floor protection in the exact location
where it is to be located, making sure all minimum clearances
are met. Mark the floor protection where the pedestal will be
located, then remove the stove.
7. Make four 1-1/2” (38 mm) cuts in one end of the corrugated
tube and fold the flaps back. Cut a 4” (102 mm) hole through
the floor protection and the floor and insert the corrugated tube
into the hole. Cover it with the supplied screen and fasten it to
the floor protector.
PEDESTAL INSTALLATION
(For ash drawer pedestal see instructions included with pedestal)
Residential and Mobile Homes
(Bolting down and grounding are required only in mobile homes)
CAUTION: Wear gloves during installation in case of sharp
edges on the stove.
1. Remove the heater from the carton, if packaged, upon receipt
and check for any damaged or missing parts.
2. Carefullyputthestoveonpedestalwiththeopenendofthepedestal
facing the rear. DO NOT LEAVE THE STOVE UNATTENDED
UNTIL IT IS BOLTED SECURELY TO THE PEDESTAL.
3. Lineuptheholesinthebracketsonthepedestalwiththethreaded
holes in the bottom of the stove. Use the two 1/2” long bolts
and 3/8” standard washers to bolt the stove to the pedestal. Be
sure to see that the stove is mounted squarely on the pedestal
before tightening the two bolts securely.
4. When installing a pedestal on this stove you MUST plug the four
leg mounting bolt holes, located on the bottom of the stove in
the four corners, with the bolts that were used to mount the
shipping legs. The two rear bolts should not be installed more
thantwofullrotationstopreventliftingthebricksoffthebottom
of the stove. FAILURE TO INSTALL THESE FOUR BOLTS
PROPERLYWILLRESULTINREDUCEDCONTROLOFTHE
STOVE’S COMBUSTION SYSTEM!
8. Locate the 11-1/2” x 14” (292 mm x 356 mm) metal plate and
paint to match the stove if necessary. Position this piece so that
the 14” (356 mm) dimension evenly overlaps the lips on the back
of the pedestal (see drawing below). Attach this plate to the back
of the pedestal with the self-tapping screws supplied.
9. If the stove is to be fastened to the floor, attach the stove with
the supplied lag bolts, through the pedestal base on opposite
sides, attaching them into the floor beneath the floor protection.
Seal any irregularities with silicone sealer.
10. If installed in a mobile home, the heater shall be grounded to the
chassis with a #8 AGW copper wire or equivalent.
11. Install bricks as per instructions on Pages 14 and 15. It is highly
recommended that the baffle be assembled before the chimney
is installed so that the baffle blankets can be adjusted into place
from the flue outlet.
12. Install chimney as per manufacturer’s instructions.
Block Off Plate is
Required When
Installing Outside
Air Into Unit (Plate
is Included With
Kit # 71112)
Figure 13
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
13
POST INSTALLATION CHECKS
BRICK INSTALLATION
CAUTION: Wear gloves during brick installation in case of
sharp edges inside the stove.
1. Check that all chimney pipe joints are securely fastened.
2. Check that the heater is securely fastened to the floor (if ap-
plicable).
Note: Installation of the baffle boards and baffle blankets are easier when
you can still access the flue outlet, (before connecting the flue vent). Be
sure the baffle blankets are placed flat on the baffle boards so as not
to block exhaust flow to the flue. Use a ruler or a piece of kindling to
reach over the baffle blanket to be sure it is completely flat on top of the
baffle boards.
3. Make sure the intake vent has clear access to outside air (if ap-
plicable).
4. Make sure the outside air vent has been sealed properly to keep
rodents out (if applicable).
Measure bricks before installing, as per list of dimensions on next
page, to be sure the correct bricks are installed in the correct location.
5. Be sure all roof flashings are watertight.
1. Install bricks #1-26 in the numbered sequence shown in Figure
6. Be sure the stove is properly grounded (if applicable).
14 on Page 15.
FOR YOUR OWN PROTECTION AND INSURANCE PURPOSES,
HAVE YOUR CHIMNEY AND CONNECTOR PIPE INSTALLATION
INSPECTED BY YOUR LOCAL BUILDING CODE AUTHORITY OR
FIRE MARSHAL BEFORE STARTING A FIRE IN YOUR STOVE.
NOTIFY YOUR INSURANCE COMPANY.
Note: Beforeinstallingyourbaffleboardsmakesurethestainless
steel tube support and front and rear tube hangers are centered
side to side and that the front and rear hangers are hooked onto
the stainless steel pins protruding from the rear of the airwash
and the stove back.
2. Next,youwillinstallthebaffleboards. All4baffleboardsincluded
are the same size. You will start by installing the boards in the
center part of the unit on top of the secondary tubes to each side
of the baffle support with the 15” side of the baffle board going
from the front to back of the unit. Once you have the first two
boards installed slide the board to the left side of the baffle sup-
port all the way to the left and rear of the unit. You will slide the
board to the right side of the secondary support to the right and
rear of the unit. Next you will install the two remaining boards
where you originally installed the first two boards on each side
of the baffle support and pushed against the rear of the unit. The
stainless steel support hanger should be centered left to right
between the sets of baffle boards and placed as shown in Figure
15 on Page 15.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
14
3. Also included with the unit are two 15” x 10” x 1” thick baffle blankets. Install each blanket above the baffle board to each side of the second-
ary support with the 15” side of the blanket from front to rear of the unit. Make sure that the baffle blankets are to the full rear of the unit.
CAUTION: Make sure the baffle blankets are down flat on the baffle boards, pulled together in the center so that no gaps
exists between them and do not protrude beyond baffle boards. It is critical that baffle boards and baffle blankets are fully
against the rear of the unit.
These brick sizes may be slightly smaller to adjust for steel and firebrick tolerances beyond our control. Be sure to measure and mark bricks
with their numbers when removing.
WARNING: IF THE BRICKS ARE NOT INSTALLED EXACTLY AS SHOWN BELOW, THEY COULD FALL OUT OF PLACE DURING RE-
FUELING OR BURNING OF THE STOVE CAUSING SERIOUS INJURY.
Firebox Brick Layout as Viewed from the Front
24
E
25
H
26
E
Brick Sizes
B = 4-1/2”x 5-1/2”
1
F
2
F
3
G
4
F
5
F
10*
F
6*
F
E = 3”x 9”
11
F
7
F
F = 4-1/2”x 9”
G = 1-1/2”x 9”
H = 1-1/2”x 3”
K = 1-1/2”x 5-1/2”
S = 2-1/8”x 9”
8
F
12
F
14
F
15
F
17
F
18
F
16
G
13
S
9
S
23
B
19
B
22
B
21
K
20
B
* Bricks 6 and 10 fit up against the back of the firebox.
Figure 14
Baffle Insulation Parts
Side Cut-A-Way View of Firebox
15”
Baffle Blankets
1” Thickness
Two Baffle Blankets Per Unit
Baffle
Board
10”
15”
Firebox
Brick
1/2” Thickness
Four Boards Per Unit
4-3/4”
Figure 15
Figure 16
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
15
OPERATING HINTS
STARTING AND MAINTAINING A FIRE
Be sure to clean plated accessories with a household type
cleaner and a very soft cloth to remove any fingerprints and
residues prior to the first fire.
1. Burn only dry, well-seasoned wood for maximum heat output. In some
states it is illegal to burn wet wood or anything other than clean, dry
wood products.
2. Your stove is designed to operate with the door closed! Operate only
with the door shut tightly at all times except when loading wood and
possibly on start up to establish a draft. Never leave the unit unat-
tended while the front door is slightly opened.
1. NEVER USE FLAMMABLE LIqUIDS TO START OR REKINDLE
A SOLID FUEL FIRE!!
3. DONOThitormovethebaffleboardswhileloadingwood.Occasionally
check the baffle. Make sure the baffle blankets are always flush with
the front of the baffle boards. Loading oversized logs may dislodge
the baffle boards.
4. CAUTION: THE DRAFT CONTROL MUST BE FULLY OPEN BE-
FOREOPENINGTHEDOORTOAVOIDPOSSIBLECOMBUSTION
FLASH!! (Ignition of hot volatile gases as the door is opened).
5. Feeding excessive amounts of fuel to the stove should be avoided.
It is important to supply it with sufficient draft and fuel to maintain a
moderatelyhotfire.If,duringovernightburns,heavycreosotedeposits
develop inside your stove and on the door, the draft is set too low
- review your burning habits!
2. Fully open the primary draft control by pulling the 1” plastic knob
out on the left side (lower front corner) until it stops (away from the
stove). This control determines the amount of air entering the stove.
Pushing it toward the stove reduces the burn rate in the firebox. For
your convenience, the rod on this control is marked with four grooves
to assist you in obtaining repeatable burn rates.
3. Place a small amount of crumpled paper in front of the firebox and
cover it with a few pieces of kindling.
4. Light the paper and allow sufficient time for the kindling to become
fully engulfed in flames. You will now close the wood units front door.
(Your wood units front door may or may not need to be left slightly
open during this start up process, this depends on the stove model
and the amount of draft present. Do not leave the unit unattended
while the front door is slightly open) Once kindling is burning well,
larger pieces of wood may be added, then the door should be fully
closed if there was the need to keep it slightly open during start up.
CAUTION
Be careful not to abuse door assembly by striking or
slamming it. If the door assembly or glass is broken or
damaged, they must be replaced with factory original
parts before heater can be safely operated. Use only
components provided by the manufacturer as replace-
ment parts.
DO NOT LEAVE THE STOVE UNATTENDED WHILE THE FRONT
DOOR IS SLIGHTLY OPEN.
CAUTION: Do Not alter the adjustment range of the draft
control for increased firing for any reason.
OK
Operate only with fuel door and ash drawer closed. Maintain
allsealsingoodcondition.Donotoperatewithbrokenglass.
Do Not build the fire too close to the glass.
Donotoperatetheappliancewiththedooropenorajarother
than possibly during start up to create a draft (Do not leave
the unit unattended while the front door is slightly open dur-
ing start up). Operating the appliance with the door open
other then in initial start up if needed will produce extreme
temperatures within the appliance. Damage caused from
over-firing is not covered under the manufacturers limited
warranty.
5. For best results, use smaller pieces of wood to get the insert tem-
perature very high before loading larger wood for sustained burns.
If necessary, crack the door to allow ignition of the fuel charge. Do
not leave the unit unattended while the front door is slightly open.
Now you can add larger pieces of wood and after several minutes of
high burn, set the left control for the desired heat output. Check the
exhaust in about 15 to 20 minutes. Large amounts of smoke indicate
an improper burn setting (either too high or too low). Adjust and
recheck in 5 to 10 minutes.
Figure 17
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
16
BLOWER OPERATION
Blower Operation
The blower can be operated manually or automatically (blower will
turn on when the stove is hot and turn off when the stove is cool).
The rocker switch on the control panel allows you to select between
manual operation or automatic operation as follows (see Figure 19):
MANUAL OPERATION: Turn rocker switch to the “MANU-
AL” position and adjust rheostat knob to the desired speed. The blower
will have to be manually turned “OFF” by rotating the rheostat knob
clockwise until it clicks.
Blower Speed Control
Knob (rheostat)
Manual / Auto
Rocker Switch
Figure 19 - Blower Controls
AUTO OPERATION: Turn rocker switch to the “AUTO” posi-
tion and the rheostat to the ON position (rotate rheostat knob coun-
terclockwise until it clicks). When the stove warms up, the blower will
automatically turn on (adjust rheostat knob to the desired speed set-
ting). When the stove cools down, the blower will automatically turn
off.
WARNINGS
The blower must be plugged directly into a properly
groundedthree-prongreceptacle,120VAC,60Hz,single
phase. Do not cut or remove the grounding prong from
this plug. Do not route power cord under or in front of
appliance.
Rheostat Operation - The highest blower speed is obtained by turn-
ing the rheostat knob counterclockwise until it clicks “ON”, then rotate
towards “HIGH” to increase blower speed. Rotate the knob clockwise
for a lower speed. To turn off, continue to rotate the knob clockwise
until it clicks “OFF.”
Installation must be in accordance with National Elec-
trical Code, ANSI/NFPA 70 - latest edition. In Canada,
the current CSA C22-1 Canadian Electrical Code - latest
edition.
Blower Operation Guidelines
While in auto operation mode, the blower will turn off and on based on
the temperature of the appliance. Auto operation ensures there is suffi-
cient heat build-up to warm the air being moved by the blower before the
blower is turned on. Likewise, when the appliance cools off, the blower
is turned off to prevent circulating cool air. Depending on the size and
intensity of the fire it may be necessary to adjust the blower speed ac-
cordingly to ensure un-interrupted blower operation. For example a small
fire may require a slower blower speed to keep the heat output by the
blower consistent. If the blower is operated in manual mode, it may be
necessary to adjust the blower speed as the fire begins to burn down and
the appliance is no longer hot enough to effectively heat the air moved
by the blower. If the air coming from the blower feels cool, one should
either decrease the blower speed or stoke the fire to build up more heat.
DANGER: Disconnect power before servicing blower.
In the event that you remove the blower for any reason,
make sure a cover plate (available from Lennox Hearth
Products)isinstalledbeforeusingtheheater.Excessive
rear wall temperatures will result if the stove is burned
withoutthecoverplate. Thecoverplateisnotnecessary
ifablowerhasneverbeeninstalledbecauseaknock-out
will be in place to act as the cover.
AUTO-RESET
TEMPERATURE
NOTE: Turn blower off before opening the door to load the fuel.
ROOM AIR
SWITCH N/O
BLOWER
TWO POSITION
SWITCH
MANUAL/TEMPERATURE
NOTE: SWITCH CONDITIONS
GIVEN AT ROOM TEMPERATURE
N/C = NORMALLY CLOSED
N/O = NORMALLY OPEN
3-RED
1-BRN
3-RED
YLW
= FEMALE DISCONNECT
= MALE DISCONNECT
= STUD CONNECTION
3-RED
1-BRN
WHT
SPEED
CONTROL/OFF
POWER CORD
4-GRN
4-GRN
BLK
Figure 18 - Blower Wiring Schematic
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
17
OPERATING TECHNIqUES AND HINTS
ACHIEVING CLEAN, LONG BURNS
Recentdevelopmentsinwoodburningtechnologyhavemadewoodburning
a cleaner and more convenient way to heat your home. Overall efficiency
in a wood burning appliance is a combination of combustion efficiency
and heat transfer efficiency. Whether heating your entire home or just a
room or two, your understanding of how to best operate your stove or
insert will enhance its overall efficiency and performance. What this can
mean to you is longer, cleaner burns, less wood use and more heat.
To achieve long burn times, after having thoroughly preheated the
stove, let the stovetop cool down to 275 to 400 degrees (on Elites,
locate thermometer on the face of the insert just above the door). Now
load the firebox and set the draft control. At this point, you may need to
burn the stove with the draft open for a few minutes to ignite the wood.
All Lennox Hearth Products stoves are EPA tested for emissions at low
burn with the air control completely closed. Whether or not you should
burn your stove with the air control completely closed will depend on
the following factors:
GETTING THE MOST OUT OF YOUR STOVE
*
*
*
*
*
How you load your wood
Your chimney type, height and draft
Your wood type and its moisture content
The temperature of the stove
The following sections will outline techniques you can use to “get the
most out of your stove.” Please read them carefully.
Which model stove or insert you have
MAXIMIZING YOUR STOVE’S OVERALL EFFICIENCY
Experiment with different loading configurations to achieve longer
burns. Try loading the wood from side to side and nesting it in the ashes
to prevent airflow under and around the wood. Fresh wood should be
loaded to the back of the firebox or to the sides. Hot coals or half burned
wood should be brought towards the front of the firebox. The way you
load your wood can seriously affect burn times. If the new load does not
ignitewithinafewminutes,trycrisscrossingtheloadtoallowmoreairflow
around the fire, or try a slightly hotter stove temperature.
It is important to know that for high, combustion efficient, clean burns,
you will need to have sufficient temperatures inside the firebox for
thorough combustion. The best method for determining if you have
sufficient temperatures is to watch the brick lining in your firebox. When
you first light your stove, the bricks will turn a dark brown or black.
After 20 to 30 minutes of a hot fire, most of the bricks should return
to near their original light brown or yellow color. This means the bricks
have reached a high enough temperature for your stove to achieve high
combustion efficiency.
Determining the lowest setting for efficient low burns. This will require
some experimentation on your part. Try closing the air control all the
way with the stove temperature at 325 to 350 degrees. If the flames are
completely extinguished, open the air control halfway and then slowly
close it until there is only a small amount of flame. It is important to check
the stove about 20 minutes after setting the draft control as it takes this
long for the stove temperature to stabilize. There should still be some
small flames on or above the wood load.
Second and just as important, is achieving a high level of heat transfer
efficiency. Slowing the rate of flow through the stove or insert enhances
heat transfer, thus allowing more time for heat to be transferred into your
home. To do this, be sure to thoroughly preheat your stove and then
reduce the amount of primary air by closing the draft control (lower left)
to about 1/2 to 3/4 open. This will decrease the excess oxygen in your
flue, which carries heat up your chimney, but should still be enough
air to allow the stove to produce its maximum heat output. (More air
may produce a slightly greater amount of heat, but will greatly increase
wood consumption). When the area being heated reaches a comfortable
temperature, slow the burn rate by closing the control to further improve
heat transfer.
Use 325 degrees as a starting point. You can try starting temperatures
25degreeshigherorlowertoachievedesiredburntimes, start25degrees
lower if the stove burns the wood too quickly or 25 degrees higher if there
are no flames in the firebox for more than a few minutes after loading the
wood. You may or may not need to burn the stove with the air control
open for a few minutes prior to setting the draft for a low burn, this will
depend on the factors mentioned above. Be sure not to smolder a fire
overnight. Check your chimney for large amounts of smoke as this
indicates very poor combustion.
To get the most out of your appliance, you will need to combine good
combustion efficiency with good heat transfer practices. The following
are some tips on how to operate your stove to achieve the highest overall
efficiency.
It is important to realize that stove technology has changed. Stoves
have changed a great deal in the last few years. This has led to substantial
changes in the methods of operation in new stoves as compared to older
stoves. In old stoves without full brick linings and ceramic insulation,
the rule was “get the stove as hot as possible before setting the draft on
low for overnight burns.” On newer, high technology stoves, this is not
necessary. Although it is still important to have the stove hot enough to
burn efficiently, it will require less preheating. Once you have determined
your optimum operating temperatures for various burn rates, we believe
you will find your stove an extremely convenient way to achieve your
heating needs.
1. Thoroughlypreheatyourstovebeforeslowingtheburnratebyclosing
the draft control.
2. Measure the stove temperature at the hottest point on the stove top
or face. Use this information to repeat burn rates.
3. Once preheated, add wood (if needed) and partially close the draft
control (lower left).
4. Operate your stove as much as possible in the low to medium burn
ranges.
5. Do not lower the draft setting so low as to completely extinguish the
flames in the firebox. Check for at least some small flames twenty
minutes after setting the draft control.
6. Do not continually operate your stove in the high (wide open) setting.
This wastes wood by carrying a great deal of heat up the chimney
and can damage your stove and chimney.
7. Go outside and check your chimney. More than a very small amount
of smoke indicates wasted heat, creosote build up and pollution.
Do not reload the stove for long burns when the stainless secondary
tubes or baffles are glowing red, or when the stove is uncomfortably
hot to load. This indicates the stove is too hot to load for a long burn.
Also, do not load wood for a long burn on a deep bed of hot coals. Try
stirring the coals a few minutes before loading the stove for a low burn
to allow some of the unburned coals time to burn.
18
MAINTENANCE
CAUTION
Cleaning Glass: Ensure appliance is cold prior
to cleaning glass. A commercial glass cleaner
designed for stoves is recommended. Do not use
abrasivecleaners.Donotcleanwithanymaterials,
which may scratch or otherwise damage the glass.
Scratches on the glass can develop into cracks or
break. Inspect the glass regularly. If you detect a
crack, extinguish the fire and contact your dealer
for a replacement.
DOOR HINGES: If door hinges need lubricating, use an anti-seize com-
pound (never use oil) available from your Lennox Hearth Products dealer.
DOOR LATCH: If your door latch fails to latch tightly and the gasket is
in good condition, place a length of pipe (cheater bar) over the inside
portion of the door handle and bend slightly toward the door until the
proper adjustment is obtained. If the door handle does not close easily,
apply high temperature anti-seize to the striker.
DOOR GASKET: Periodically check gasket to make sure it is not over-
compressed. If compressed, replace with a special woven Door Rope.
(Don’t try substituting rope, only use special Lennox Hearth Products
Door Rope).
GLASS REPLACEMENT INSTRUCTIONS
PLATED ACCESSORIES: Clean only with household type glass cleaner
and a very soft cotton cloth. Other products may damage plated finish,
paint and gaskets.
Step 1. Remove Door Assembly - Open door to remove E clip from the upper
hinge pin. Remove upper hinge pin by pulling up while holding the op-
posite side of the door. Lift door out of the lower hinge pin and place
face down on a soft surface.
Step 2. Remove Door Back Screws (6 ea.) - Using a 5/32” allen wrench remove
the 6 retainer screws from the faceplate. To locate screws, peel back the
door gasket as necessary.
Step 3. Disassemble Door Assembly - Flip door assembly over to be face up.
Separate faceplate from door back by pulling up on faceplate.
Step 4. Remove Glass - Carefully remove broken glass one piece at a time
(protective gloves are recommended)
BAFFLE BLANKET: Your baffle blankets should be inspected during every
chimney cleaning. If the baffle blanket is compressed or heavily stained,
it should be replaced. Heavy creosote stains or matting is an indication
of improper use and your burning habits should be reviewed.
GLASS CLEANING: Only clean glass with products specifically made to
use on wood stoves. Other products could damage gaskets and paint.
Never scrape glass with a razor blade. This can pit the glass and make it
impossible to clean in the future.
WINDOW GASKET: The window gasket can be checked by running the
flame of a match near the gasket and around the door. If the flame is
drawn in around the window, the gasket should be replaced.
Step 5. Install New Glass Assembly - Install the new glass with gasket in recess
on door back (use only factory supplied 5mm ceramic glass. Do not
substitute).
Step 6. Reinstall Faceplate and Screws - Reinstall faceplate onto door back
and while holding the door assembly together flip the assembly back
onto it’s face. Carefully reinstall the screws. Be very careful not to
overtighten the screws (this could result in glass breakage when the
stove or fireplace insert is hot) and it is highly recommended to use anti
seize on the screws.
Step 7. Reinstall Door - Set door assembly back into the lower hinge mount
while holding the handle side of the door up. Place the upper hinge
pin back in the mount and door assembly. Reinstall the E clip that was
removed.
DOOR HANDLE: Door handle may become tight as you use the stove.
Free the handle up by using dry graphite supplied with the stove. The
directions are included with the graphite.
WARNING
Inspectandcleanchimneyandconnectorfrequently.
Under certain conditions of use, creosote buildup
may occur rapidly.
GLASS CLEANING GUIDELINES
Door Gasket
WARNING: DO NOT CLEAN GLASS WHEN APPLIANCE IS HOT!
Screws and
Washers
Glass on any wood stove or fireplace insert will not stay perfectly clean.
Here are some guidelines for cleaning and caring for the glass:
•
•
Ensure the stove or fireplace insert is cold prior to cleaning glass.
This appliance is designed to provide a flow of air over the inside of
the glass, where along with high heat helps inhibit build-up on the
glass. When build-up occurs, a commercial glass cleaner designed
for stoves is recommended. Regular household glass cleaners will
not clean creosote.
Door Back
•
•
Do not use abrasives such as steel pads, steel wool or oven cleaner
as they will scratch the glass. Never scrape glass with a razor blade
as this may pit the glass and make it impossible to clean in the future.
Do not use chemical glass cleaners as they may damage the gaskets
or painted surfaces.
Handle Rod
Glass
Glass Gasket
TIPS FOR KEEPING THE GLASS CLEAN
•
•
Burn only dry seasoned cord wood. Wet wood = Dirty glass.
A short, hot fire (15 - 20 minutes) may help to clean off some of the
normal buildup. Lower burns = more build-up. Higher burns = less
build-up.
Faceplate
•
•
Keep freshly loaded wood away from the glass.
After reloading, allow all the wood to catch flame before dampering
down the stove or fireplace insert.
Figure 20
19
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
TROUBLESHOOTING
Problem
Solution
POOR DRAFT:
Extend chimney in length or have the chimney realigned to the proper size flue. Oversized chimneys normally have
poor drafts. Remember, the stoves’ draft depend solely on the natural draft of the chimney (See Draft Requirements on
Page 4). If your stove is not drafting properly, your chimney is the problem. All stoves are thoroughly tested to ensure
proper draft with the correct size chimney flue.
EXCESSIVE DRAFT:
DIRTY GLASS:
With better chimneys being more common, excessive draft can be an issue. Alleviate excessive draft by slowing the
burn rate of the stove once it has reached proper operating temperature (See Maximizing Your Stoves Overall Efficiency
on Page 18).
1) Burn smaller, hotter fires and check to make sure you are not setting the draft down too far with the draft control.
2) Make sure your wood is well-seasoned and dry (not open to rain - see Creosote and Fuel sections on Page 5).
3) See Poor Draft section (above) and Cleaning Glass on Page 16.
SMOKES WHEN
DOOR IS OPEN:
1) If smoke is entering the room, check to make sure your baffle boards are properly installed
and that the baffle blankets are pushed back flush with the front of the baffle boards.
2) Check the chimney for blockage due to creosote (see Chimney and Creosote sections on Pages 5 and 6).
3) Check draft (See POOR DRAFT section above).
WOOD BURNS
TOO FAST:
1) The draft control must be closed further.
2) Add fuel at lower firebox temperatures.
3) Load wood side to side and reduce the flow of air under wood.
4) The door seal may need replacing, check for leakage.
5) See “Excessive Draft.”
POOR HEAT OUTPUT:
1) Check your wood. Wet, moist, unseasoned wood will not produce heat.
2) Your stove needs to be seasoned (moisture removed from the steel and brick). Continue to burn a fire. It normally
takes from one to three weeks of burning to season your stove (See Burn-In Period on Page 5).
3) See Excessive Draft section above.
PAINT GIVES OFF
ODOR (smoke):
Paint is tempering-in. Burn only moderately hot for the first few days until paint is fully cured.
Then burn a very hot fire to cure any paint that may not easily cure. Open windows or door to ventilate (See Burn-In
Period on Page 5).
20
DO’S AND DON’TS
DO NOT: Install or operate this stove before reading this manual.
DO NOT: Close the draft beyond the point at which the flames are completely extinguished.
DO NOT: Open the stove door without fully opening the draft first.
DO NOT: Burn driftwood or wood that has been in salt water. This includes some mill ends and scrap lumber that has been floated in salt water
on the way to the mill. (This will void your warranty).
DO NOT: Handle the plated faceplate unnecessarily. Use the door handle only.
DO NOT: Force oversized logs into the firebox as this may dislodge the baffle assembly.
DO NOT: Close the door tightly during Burn-In Period.
DO:
Be sure to clean any fingerprints from the Gold or Nickel faceplate before burning the stove. Clean the Gold or Nickel door only with a
household type glass cleaner and a very soft cloth.
DO:
DO:
Consult local building department if other than recommended clearances are desired.
Read instructions for the baffle boards and baffle blankets occasionally to ensure you have not bumped or moved them out of place
when loading wood.
DO:
DO:
DO:
DO:
Check the chimney and baffle monthly to make sure they are clean.
Burn seasoned, dry wood only! (RAIN = WET WOOD)
Open the door frequently during Burn-In Period to keep gasket from adhering to the curing paint.
Enjoy the warm feeling of your new Lennox Hearth Products appliance.
21
20
21
H5558 Single Black Cascade Leg
REPLACEMENTPARTS-MODELSSS210,ST210ANDSWS210
H5669 Single Black Olympic Leg
H5622 Single Gold Olympic Leg
Contact an Lennox Hearth Products dealer to obtain any of these
parts.Neverusesubstitutematerials.Useofnon-approvedparts
can result in poor performance and safety hazards.
H5621 Single Nickel Olympic Leg
H5620 Single Brushed Gold Olympic Leg
H5619 Single Brushed Nickel Olympic Leg
H5649 Heatshield / Leg Fastener Kit
71115 Bottom Heatshield / SS210, ST210 and SWS210
H5662 Cascade / Olympic Leg Kit Outside Air Plenum Box
FSB BLOWER PARTS
FRONT DOOR PARTS LIST
22
23
24
Item # Cat. No
Description
1
2
3
4
6
7
H5639 Door Rope Kit, 7/8” Dia. (6’ 2”)
H5629 Upper Hinge Pin
H5626 Upper Hinge Pin E-Clip
25
H8062 FSB700 Blower Only Assembly w/ blower wiring
harness
H5628 Lower Hinge Pin
26
27
28
29
30
31
H5658 Fan Blade (FSB700)
H5640 Glass Gasket Kit (8’ 4”)
H5657 Fan Cage (FSB700)
H5577 Set of 6 screws and 6 washers for door assembly
H5654 Spring Handle / Nickel
H8063 FSB700 Blower Only Wire Harness
H8064 Snap Switch w/gasket and screws
H5742 Speed Control - High Temperature (FSB700)
8
H5653 Spring Handle / Gold
71067 Traditional Door Glass / Plain
71068 Traditional Door Glass / Sailboat
71063 Traditional Door Glass / Cattail
71065 Traditional Door Glass / Evergreen
71066 Traditional Door Glass / Floral
71057 Traditional Door Faceplate / Black
71058 Traditional Door Faceplate / Gold
71059 Traditional Door Faceplate / Nickel
71148 Traditional Door Faceplate / Brushed Gold
71145 Traditional Door Faceplate / Brushed Nickel
71072 Arch Door Glass / Plain
H8065 Control Panel Assembly w/ Snap Switch Housing
Assembly
9
32
H8066 Control Switch (Manual, Off, Automatic)
MISCELLANEOUS PARTS
71052 Dry Graphite (Apply to door handle and door hinges)
H5633 Anti Seize 2 gram pouch
71134 Stainless Steel Pipe Reducer from 8” to 6”
SS210, ST210 AND SWS210 STOVE PARTS
H5627 Removable Inner Flue Collar Ring
H8079 Nameplate Kit w/ Hardware - Silver
H8080 Nameplate Kit w/ Hardware - Gold
H5650 Draft Rod Knob
10
11
12
33
34
71073 Arch Door Glass / Sailboat
71069 Arch Door Glass / Cattail
35
36
37
38
39
40
41
42
43
44
45
46
H8081 Ash Block Off - Hearthplate
71070 Arch Door Glass / Evergreen
71071 Arch Door Glass / Floral
H5661 Cast Iron Ash Plug
H5582 1/2 Cut Brick for Ash Removal
H5612 Firebrick 4-1/2” x 9” (14 per stove)
H5606 Firebrick 4-1/2” x 5-1/2” (4 per stove)
H5605 Firebrick 3” x 9” (2 per stove)
H5611 Firebrick 2-1/8” x 9” (2 per stove)
H5599 Firebrick 1-1/2” x 9” (2 per stove)
H3096 Firebrick 1-1/2” x 5-1/2” (1 per stove)
H5603 Firebrick 1-1/2” x 3” (1 per stove)
71060 Arch Door Faceplate / Black
71061 Arch Door Faceplate / Gold
71062 Arch Door Faceplate / Nickel
71147 Arch Door Faceplate / Brushed Gold
71144 Arch Door Faceplate / Brushed Nickel
13
14
H5579 Traditional Door Back w/ Handle (door gasket
included)
H5578 Arch Door Back w/ Handle (door gasket included)
ASH DRAWER PEDESTAL & PEDESTAL
H5571 Complete Baffle/Secondary Burn Tube Assembly
(includes tubes and all mounting hardware)
15
16
17
18
19
H5514 Small & Large Pedestal Rear Block Off Plate w/ Hole
H5556 Ash Drawer for Large Pedestal
47
48
H8019 Baffle Blankets 15-1/4” x 12-1/2” x 1” - Two Included
H8018 Baffle Board Kit w/ Baffle Blankets
H5564 Ash Plug Remover and Rake
H5516 Aluminum Flex Tubing Kit w/ clamp (15” of 4” dia.)
H5565 6” x 6-1/2” Rodent Screen
LEGS AND LEG PARTS
18
H5516 Aluminum Flex Tubing Kit w/ clamp (15” of 4” dia.)
22
REPLACEMENT PARTS - MODEL SS210
33
48
34
47
46
35
41
45
38
41
39
39
37
39
39
42
39
43
39
39
39
39
39
39
42
39
43
39
39
36
40
40
44
40
40
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
23
REPLACEMENT PARTS - MODEL ST210 AND SWS210
33
34
48
47
46
35
41
45
41
39
38
39
39
42
37
39
39
43
39
39
39
39
39
43
39
39
39
39
42
36
40
40
44
40
40
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
24
REPLACEMENT PARTS - MODELS SS210, ST210 AND SWS210
Door Parts
2
3
1
2
1
3
14
4
11
5
8
13
6
4
9
5
7
8
6
7
12
10
Blower Parts
25
27
28
26
29
31
30
32
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
25
REPLACEMENT PARTS - MODELS SS210, ST210 AND SWS210
Leg and Leg Parts
23
20
22
24
18
21
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
26
REPLACEMENT PARTS - MODELS SS210, ST210 AND SWS210
Ash Drawer Pedestal and Pedestal
18
19
15
17
18
16
19
15
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
27
ACCESSORIES - MODELS SS210
ACCESSORIES - MODELS ST210 AND SWS210
Product Reference Information
Product Reference Information
Description
Cat. No.
H7886
H8404
Description
Ship.
Weight
Ship.
Volume
Cat. No.
H7885
Ship.
Weight
Ship.
Volume
424 lb.
424 lb.
20.74 cu. ft.
20.74 cu. ft.
ST210A-B, Stove / Step Top / Arch
Black Door / Nickel Nameplate
411 lb.
26.23 cu. ft.
SS210T-B, Stove / T Top / Traditional
Black Door / Nickel Nameplate
SWS210, Stove / Step Top / Arch Black
Door
PEDESTALS (REqUIRED)
PEDESTALS (REqUIRED)
Cat. No.
71113
71114
Model
WL-PED
Description
Cat. No.
71113
Model
WL-PED
Description
Pedestal (ref. form #506033-16)
Pedestal
WL-PED-ASHD
Ash Drawer Pedestal (ref. form #506033-15)
71114
WL-PED-ASHD
Ash Drawer Pedestal
OR LEGS (REqUIRED) (ref. form #506033-14)
OR LEGS (REqUIRED)
70000
70001
70002
70007
LEG-OLY-B
LEG-OLY-G
LEG-OLY-N
LEG-OLY-BRG
Olympic Sculptured Black Legs (4 per pkg.)
Olympic Sculptured Gold Legs (4 per pkg.)
Olympic Sculptured Nickel Legs (4 per pkg.)
70000
70001
70002
70007
LEG-OLY-B
LEG-OLY-G
LEG-OLY-N
LEG-OLY-BRG
Olympic Sculptured Black Legs (4 per pkg.)
Olympic Sculptured Gold Legs (4 per pkg.)
Olympic Sculptured Nickel Legs (4 per pkg.)
Olympic Sculptured Brushed Gold Legs
(4 per pkg.)
Olympic Sculptured Brushed Gold Legs (4
per pkg.)
70008
70003
LEG-OLY-BRN
LEG-CAS-B
Olympic Sculptured Brushed Nickel Legs
(4 per pkg.)
70008
70003
LEG-OLY-BRN
LEG-CAS-B
Olympic Sculptured Brushed Nickel Legs (4
per pkg.)
Cascade Steel Black Legs (4 per pkg.)
Cascade Steel Black Legs (4 per pkg.)
HEAT SHIELD (REqUIRED WITH LEGS)
HEAT SHIELD (REqUIRED WITH LEGS)
71115
WSHS-210
Heat Shield (ref. form #506033-14)
71115
WSHS-210
Heat Shield
FACEPLATE KITS (INCLUDES FACEPLATE, HANDLE AND NAMEPLATE)
H7901 ARCH-FPK-BG Arch Faceplate/Brushed Gold
H7902 TRAD-FPK-BG-SM Sm - Traditional Faceplate/Brushed Gold
FACEPLATE KITS (INCLUDES FACEPLATE, HANDLE AND NAMEPLATE)
H7901
H7902
H7904
H7905
ARCH-FPK-BG
Arch Faceplate/Brushed Gold
TRAD-FPK-BG-SM Sm - Traditional Faceplate/Brushed Gold
H7904
H7905
ARCH-FPK-G
Arch Faceplate/Gold
ARCH-FPK-G
Arch Faceplate/Gold
Traditional Faceplate/Gold
BLOWER
TRAD-FPK-G-SM Traditional Faceplate/Gold
BLOWER
TRAD-FPK-G-SM
H7917
BLWR-FSB700-SS Blower Kit, FS Woodstoves
OUTSIDE AIR KITS
H7917
BLWR-FSB700-SS Blower Kit, FS Woodstoves
OUTSIDE AIR KITS
71111
71112
OUTAIRK-L
OUTAIRK-P
Outside Air Kit / Leg (ref. form #506033-18)
71111
71112
OUTAIRK-L
OUTAIRK-P
Outside Air Kit / Leg
Outside Air Kit / Pedestal
MISC.
Outside Air Kit / Pedestal (ref. form #506033-17)
MISC.
71053 Paint Gold (1/2 Pint) Paint Gold (1/2 pint)
71053
71054
H8159
Paint Gold (1/2 Pint) Paint Gold (1/2 pint)
PaintNickel(1/2Pint)
TSPK-B
71054
H8159
Paint Nickel (1/2 pint)
Paint Nickel (1/2 Pint)
TSPK-B
Paint Nickel (1/2 pint)
Touch-Up Paint , Metallic Black, 12 oz.
Aerosol
Touch-Up Paint , Metallic Black, 12 oz.
Aerosol
H5308
W-LEGF-LBRKT
Leg Fastening L - Brackets (4 per pkg.) (Tie
down kit to be used in mobile or modular
homes) (ref. form #506033-19)
H5308
W-LEGF-LBRKT
Leg Fastening L - Brackets (4 per pkg.) (Tie
down kit to be used in mobile or modular
homes) (ref. form #506033-18)
28
Secure Black™ Single Wall Stove Pipe
6” SW Pipe and Accessories
ACCESSORIES - MODELS SS210, ST210 AND SWS210
Security Chimneys™ Pipe
Cat. No.
6SWL6
Model
Description
LENGTH 6” X 6”
Pc. / Container
6SWL6
100
5
6SWL12
6SWL24
6SWL36
6SWL48
6SWLT
6SWL12 LENGTH 6” X 12”
6SWL24 LENGTH 6” X 24”
6SWL36 LENGTH 6” X 36”
6SWL48 LENGTH 6” X 48”
Tubinox Components
10
2
6” Rigid Stainless Steel Liner
Cat. No.
6LL6
Model
6LL6
Description
LENGTH 6” X 6”
Pc. / Container
5
4
4
4
4
4
4
4
10
4
4
4
4
5
1
5
5
4
4
4
6SWLT
6SWLA
6SWMA
6SWT
TELESCOPIC LENGTH 6” (42”-
1
6LL12
6LL24
6LL36
6LL48
6L7A
6LL12
6LL24
6LL36
6LL48
6L7A
LENGTH 6” X 12”
66”)
LENGTH 6” X 24”
6SWLA
6SWMA
ADJUSTABLE LENGTH 6”
(3”- 9”)
5
1
LENGTH 6” X 36”
LENGTH 6” X 48”
SINGLE WALL MASONRY
ADAPTOR 6”
ADJUSTABLE LENGTH (7 to 11)
SPLIT BASE TEE
6SWT
TEE 6” (TEE CAP INCLUDED)
2
4
6LT
6LT
6SWE45
6SWE90
6SWE45 ELBOW 45 DEGREE 6”
6SWE90 ELBOW 90 DEGREE 6”
6LTCS
6LTC
6LTCS
6LTC
TEE CAP
4
TWIST LOCK TEE CAP
ELBOW 30 DEGREE
ELBOW 45 DEGREE
ELBOW 90 DEGREE
FLASHING
6SWE90A 6SWE90A SWIVEL 90 DEGREE ELBOW 6”
10
10
8
6LE30
6LE45
6LE90
6LST
6LE30
6LE45
6LE90
6LST
6UP
6UP
FLUE EXTENSION 6”
6SWAB
6SWIN7
6SWIN8
6SWOA
6SWLK
6PB
6SWAB
6SWIN7
6SWIN8
6SWOA
6SWLK
6PB
STOVE ADAPTOR 6”
INCREASER LENGTH ( 6”- 7”)
INCREASER LENGTH (6”- 8”)
OVAL TO ROUND ADAPTOR 6”
DAMPER UNIT 6”
4
4
6LSTSS
6LSA
6LSTSS
6LSA
FLASHING STAINLESS
SUPPORT ASSEMBLY
INTERIOR SUPPORT
ADAPTOR FLEX PIPE (MALE)
ADAPTOR FLEX PIPE (FEMALE)
5
4
6LSB
6LSB
DECORATIVE COLLAR 6”
(ASHT)
25
6LAAM
6LAAF
6LLFLEX
6LAAM
6LAAF
6LLFLEX
6PF
6PF
TRIM COLLAR 6” (ASHT)
5
STAINLESS FLEXIBLE LENGTH
(6”X60”)
Double Wall Black Stove Pipe
6” DL Pipe and Accessories
6LMA
6LLR5
6LLW7
6LCC
6LMA
6LLR5
6LLW7
6LCC
MASONRY ADAPTOR
REDUCER LENGTH (6”-5”)
INCREASER LENGTH (6”-7”)
DELUXE RAIN CAP
1
4
4
1
1
1
Cat. No.
6DL6
Model
Description
LENGTH 6” X 6”
Pc. / Container
6DL6
6DL12
6DL24
6DL36
6DL42A
6DL3A
6DL36A
6DT
8
4
2
2
1
4
2
4
4
4
6DL12
6DL24
6DL36
6DL42A
6DL3A
6DL36A
6DT
LENGTH 6” X 12”
6LCS
6LCS
REGULAR RAIN CAP
LENGTH 6” X 24”
6LRSMI
6LRSMI
ADJUSTABLE INSULATION
WALL THIMBLE 6” - 12”
LENGTH 6” X 36”
TELESCOPIC LENGTH (42” 66”)
ADJUSTABLE LENGTH (3”- 9”)
ADJUSTABLE LENGTH ( 3”-34”)
TEE (TEE CAP INCLUDED)
ELBOW 45 DEGREE
6DE45
6DE90
6DMA
6UP
6DE45
6DE90
6DMA
6UP
ELBOW 90 DEGREE
MASONRY ADAPTOR 1
FLUE EXTENSION 10
6DAB
6DAB
STOVE ADAPTOR 8
6DLW7
6DLW8
6DLK
6DLW7
6DLW8
6DLK
INCREASER LENGTH ( 6”- 7”)
INCREASER LENGTH (6”- 8”)
DAMPER UNIT DL 6”
DECORATIVE COLLAR
TRIM COLLAR
4
4
4
6DqDH
6Dq
6DqDH
6Dq
25
10
29
Cat. No.
Model
Description
Pc. / Container
ACCESSORIES - MODELS SS210, ST210 AND SWS210
Supports (continued)
6SM
6SM
TEE SUPPORT
1
5
Secure Temp® Factory-Built Chimney
6” Secure Temp ASHT and Secure Temp G-ASHT
6SMA
6SMA
GALVALUME ADJUSTABLE TEE
SUPPORT (2” TO 6”)
Cat. No.
Model
Description
Pc. / Container
SO
SO
OFFSET SUPPORT / WALL SUP-
PORT
10
Lengths and Fittings
6L8
6L12
6L18
6L24
6L36
6L48
6LA
6L8
6L12
6L18
6L24
6L36
6L48
6LA
LENGTH 6” X 8”
1
1
ST
ST
ROOF SUPPORT
FLOOR SUPPORT
ANCHOR PLATE
Braces and Firestops
FIRESTOP
10
5
LENGTH 6” X 12”
6SD
6SP
6SD
6SP
LENGTH 6” X 18”
1
10
LENGTH 6” X 24”
1
LENGTH 6” X 36”
1
6BF
6BF
10
LENGTH 6” X 48”
1
6RSM30 6RSM30 ANGLED FIRESTOP - 30 DEGREE
ADJUSTABLE LENGTH, 12”
INSULATED TEE (TCS INCLUDED)
1
6RS
6RS
RADIATION SHIELD
5
1
6TI
6TI
1
6RSA2
6RSA2
2PC INSULATED ATTIC RADIATION
SHIELD
6TCS
6TCS
INSULATED SS TEE CAP (INCLUDED
WITH TI)
10
6ARSA
6ARSA
ADJUSTABLE INSULATED ATTIC
RADIATION SHIELD
1
6TB
6TBS
6TBD
6TB
6TBS
6TBD
BASE TEE GALVANIZED (TC IN-
CLUDED)
1
1
1
6RSI
6RSI
INSULATED RADIATION SHIELD
INSULATED WALL THIMBLE
1
1
BASE TEE STAINLESS (TCS IN-
CLUDED)
6RSM
6RSM
6RSMI30 6RSMI30 30-DEGREE RADIATION SHIELD
1
BASE TEE GALVANIZED DOUBLE (TC
INCLUDED)
BS2
BM
BS2
BM
UNIVERSAL ROOF BRACE
UNIVERSAL WALL BAND
1
6TC
6TC
BASE TEE CAP GALVANIZED
10
5
10
10
6TCI
6TCI
INSULATED TEE CAP (USE WITH
SME SUPPORT)
6BH
6BH
GUY WIRE BAND (WIRE NOT
INCLUDED)
6TCP
6TCP
DRAIN TEE CAP (USE WITH SME
SUPPORT)
5
6FR
6FR
FLAT ROOF FLASHING
3
3
6FAR
6FAR
ADJUSTABLE ROOF FLASHING -
1/12- 7/12
6E15
6E30
6E15
6E30
INSULATED ELBOW 15 DEGREE
INSULATED ELBOW 30 DEGREE
2
1
6FARA
6FBR
6FARA
6FBR
ADJUSTABLE MALLEABLE ALUMI-
NUM ROOF FLASHING 1/12 - 7/12
Aluminum Zinc Coated Steel (Lengths and Fittings)
6GL8 LENGTH 6” X 8”
ADJUSTABLE ROOF FLASHING -
8/12- 12/12
3
6GL8
6GL12
6GL18
6GL24
6GL36
6GL48
6GLA
1
1
6GL12 LENGTH 6” X 12”
6GL18 LENGTH 6” X 18”
6GL24 LENGTH 6” X 24”
6GL36 LENGTH 6” X 36”
6GL48 LENGTH 6” X 48”
6FBRA
6FBBR
6FBRA
6FBBR
ADJUSTABLE MALLEABLE ALUMI-
NUM ROOF FLASHING 8/12 - 12/12
1
ADJUSTABLE ROOF FLASHING
12/12 - 21/12
3
1
1
6FPR
6FPBR
6FC
6FPR
6FPBR
6FC
PEAK ROOF FLASHING 1/12 -7/12
PEAK ROOF FLASHING 8/12 -12/12
STORM COLLAR
3
3
1
6GLA
6GTI
6TCS
ADJUSTABLE LENGTH, 12”
1
10
6GTI
INSULATED TEE (TCS INCLUDED)
1
Chimney Termination
RAIN CAP
6TCS
INSULATED SS TEE CAP (INCLUDED
WITH GTI)
10
6CC
PE
6CC
PE
1
UNIVERSAL SPARK ARRESTER
BAND
10
6GE15
6GE30
6GE15 INSULATED ELBOW 15 DEGREE
2
1
6GE30 INSULATED ELBOW ALUM-ZINC 30
DEGREE
Chimney Accessories
DECORATIVE TRIM
6PF
6PB
6PA
6PD
6PF
6PB
6PA
6PD
5
25
1
Supports
DECORATIVE COLLAR
BLACK PIPE ADAPTOR
FINISHING CONE
6UP
PS
6UP
PS
FLUE EXTENSION
10
1
SqUARE CATHEDRAL SUPPORT
EXTENSION
1
6SSC
6SSAC
6SFC
6SSC
SqUARE CATHEDRAL SUPPORT W/
1
1
1
Fireplace Components
COUPLER
6EK-1
6IK
6EK-1
6IK
EXTERIOR KIT (INCLUDES 1 TI, 1
TCI, 1 SME, 1 RSM, 1 CC, 1 PB,
1 BM)
1
1
6SSAC ADJUSTABLE SqUARE CATHEDRAL
SUPPORT w/COUPLER
6SFC
FINISHING SUPPORT W/COUPLER
INTERIOR KIT (INCLUDES 1 SFC, 1
RSA2, 1CC)
30
SAFETY / LISTING LABEL - ENGLISH
2011
2012 2013
31
SAFETY / LISTING LABEL - FRENCH
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
32
NOTES
33
3. The part number.
4. The description of the part.
5. The quantity required.
WARRANTY
Your wood appliance is covered by a limited warranty (provided with the
appliance). Please read the warranty to be familiar with its coverage.
6. The installation date of the appliance.
If you encounter any problems or have any questions concerning the
installation or application of this system, please contact your dealer.
Retain this manual. File it with your other documents for future refer-
ence.
LENNOX HEARTH PRODUCTS
1508 Elm Hill Pike, Suite 108
Nashville, TN 37210
1-800-9-LENNOX
REPLACEMENT PARTS
See Pages 22 through 27 for a complete replacement parts list. Use
only parts supplied from the manufacturer.
Normally, all parts should be ordered through your Lennox distributor or
dealer. Parts will be shipped at prevailing prices at time of order.
PRODUCT REFERENCE INFORMATION
Werecommendthatyourecordthefollowingimportantinformationabout
your appliance. If you did not purchase your appliance directly from a
Lennox Hearth Products dealer, then please call 1-800-9-LENNOX for the
name and phone number of your nearest Lennox Hearth Products dealer
who will answer your questions or address your concerns.
When ordering repair parts, always give the following information:
1. The model number of the appliance.
2. The serial number of the appliance.
Your Appliance’s Model Number _______________________________________
Your Appliance’s Serial Number________________________________________
The Date On Which Your Appliance Was Installed __________________________
Your Dealer's Name _________________________________________________
LennoxHearthProductsreservestherighttomakechangesatanytime,withoutnotice,indesign,
materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
Printed in U.S.A. © 2007 by Lennox Hearth Products
P/N 775215M Rev. F 09/2011
1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210
34
|
KTI Networks Network Card KG 502T User Manual
La Crosse Technology Thermometer WS 7215U IT User Manual
Lennox Hearth Indoor Fireplace SOLANA BK User Manual
LG Electronics Blu ray Player BD300 User Manual
LG Electronics Clothes Dryer DLE2140W User Manual
Lightolier Indoor Furnishings 1078 User Manual
Mackie DJ Equipment HD1221 User Manual
Maxtor Computer Drive STM3160215A User Manual
Melissa Espresso Maker 245 007 User Manual
Memorex Handheld TV MT0501 User Manual